Honda Fit Forums

Honda Fit Forums (http://www.hondafitforums.com/index.php)
-   DIYs (http://www.hondafitforums.com/forumdisplay.php?f=28)
-   -   DIY "logo" removal and painting (http://www.hondafitforums.com/showthread.php?t=2213)

claymore 06-07-2013 02:45 AM

DIY "logo" removal and painting
 
8 Attachment(s)
Well since I'm a glutton for punishment here is a short little DIY that nobody will comment on but what the heck I do them myself because they are fun. :rolleyes:

This log has been on my Jazz almost since the first day. It's from a Suzuki they sell here that is like a Suzuki Samurai they sell in the states. I had one and liked the logo so to show everybody that my Jazz was a 5 speed and not an Auto I put one on my Jazz.


as usual click to enlarge


Attachment 406


Just being antsy during my escape hole DIY I got the bug to change it's color scheme. :p

It's going to be a silver base with black letters this time.

But we have to get it off the car first. :eek:

I used the good old fishing line saw method. You just CAREFULLY pry up the end if needed and pull a length of fishing line behind the logo.


Attachment 407


Then you just pull slightly on it while using a sawing motion to cut the glue.

I wrap the line around a screwdriver handle to keep the line from cutting into my hands.


Attachment 408


Just keep pulling and sawing and soon the logo will be cut free of the glue. And the next problem comes along how the heck do you get rid of the old glue.


Attachment 409


I use a screwdriver tip and paint thinner to turn the old glue back squishy. But I am going to put the logo back in the same place and don't care what it looks like after I get the glue off.

WARNING: If you are just removing the logo and going to be running NUDE (no logo) DO NOT USE ANYTHING SHARP AS IT PROBABLY WILL SCRATCH YOUR PAINT.


Attachment 410


If you want to save the paint under the logo just soften the glue with thinner (check it on a part of the paint that can't be seen to make sure the thinner you have does not remove paint:eek:) then using a piece of cloth and just keep rubbing on the old soft glue.

I like to "roll" the old glue with the rag in one direction and it gathers up into snot balls and you can grab it and pull it off.

Once you have all the glue off by rubbing with thinner (just some on the rag not dripping it only takes a little) then the cloth and you get done you have this.


Attachment 411


Note it is not completely "clean" the rest can be removed with some cleaner wax and or polishing compound but sine I'm putting the logo back in the same spot this is clean enough for me.



The next steps are for turning the color scheme around. I dragged out my super duper sanding aid as it will come into play later.


Attachment 412


Next paint the base color first.


Attachment 413


What the heck what do you have a tiny super accurate brush and a steady hand to paint the letters black or what?????????


ANNNNTTTTT the answer will be in the next installment :rolleyes:

claymore 06-08-2013 09:28 AM

5 Attachment(s)
Well lets get on with today's installment of the DIY. :p

We left off yesterday with the logo stripped off the Jazz and painted sliver to start our conversion of the color scheme.

This shot shows the metallic in the paint really standing out in the flash.

But what the heck are those blue tails??????

as usual click on the photos to enlarge


Attachment 414


We will get back to the "tails" in a minute LOL.

The point is that I think I can apply the black paint without any slopping over onto where I don't want it using my method and I have in the past doing this kind off "painting" on parts that wouldn't allow for taping for many reasons.

BUT it the part in question has room for taping to prevent oopppsss moments better to be safe than sorry.:rolleyes:


Attachment 416

Nice and taped up.:p


Now the reason we have made "tails" becomes apparent. We are going to need some way of holding the part when we apply the paint and the "tails" make for great part handling "handles".


Attachment 415


Now the "meat" of my painting method. I use my "flat painting assistant" but any FLAT SURFACE will do. IF YOUR PAINTING SURFACE ISN'T ANYTHING OUR OTHER HALF CHERISHES WITH ALL HER HEART.

In other words something you can get paint on without ensuring your others halves wrath.

So we have our flat surface what next? Take a piece of anything you can paint without hassle even just use your flat surface but I like to tape a piece of an old car mag and tape it down so it doesn't fly away when you spray paint at it.


Attachment 417


Next grab the spray can of the paint color you want the lettering to be and have your part handy so you can grab it quickly.

Then spray a layer of paint onto your flat surface or paper. If it is hot where you are you have to move fast as the paint "skims over" very quickly.

Next grab your part, and holding it straight, press it onto the fresh paint like you were "rubber stamping" it. NOT WITH A LOT OF FORCE just touch the paint and then pull up the part and make sure all the lettering has paint on them to your satisfaction.

If it's not to hot in your area if everything didn't get a coat the first time press it into a section of the fresh paint other then the part you already pressed into and check again.

If you need to use can always spray more fresh paint into a different area and try again until you get it right.

Looking nice and new. This was right after a blast of some clear to add some protection and the weird looking section laid down nice and flat before it dried.


Attachment 418


Next up putting it back on the Jazz in the correct position. But we have to wait a bit for this puppy to get nice and dry. :rolleyes:

claymore 06-10-2013 12:59 AM

4 Attachment(s)
OK let's finish this one off.

All that is left is to slap it back on the car. So be sure to wipe down the work area first of all to remove and dirt or dust.

Then I used the old fishing line plumb bob and tape to mark where it goes. Sorry in advance for the "fuzzy" photo. :(

as usual click the photos to enlarge


Attachment 419


I used some good old "super glue" on the back as there is still most of the foam rubber backing still on the logo.

BUT "super glue" is FOREVER it leaves a nasty residue that will NOT come off. So if you are not 100% sure you will like your logo forever I would use something like "contact adhesive" that can be removed (not easily LOL).

Drum roll please....


Attachment 420


Looks good to me compared to the old look :p


Attachment 421


Attachment 422


All times are GMT -7. The time now is 08:27 AM.

Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2018, Jelsoft Enterprises Ltd.